产品搜索
在线客服
 工作时间
周一至周五 :8:30-17:30
周六至周日 :9:00-17:00
联系方式

联系人:冀柏宏

电 话:

(+86)0314-2266829

手   机:

(+86)18831479808   

(+86)13191633902   

微信:18831479808

邮 箱:btsdyb@163.com

地 址:河北省承德技术产业开发区卸甲营工业园


website qrcode

扫描查看手机版网站

产品详情
XJJ-5/50数显简支梁冲击试验机
分享到:
XJJ-5/50数显简支梁冲击试验机 
产品详情

XJJ-5/50数显简支梁冲击试验机

一. 产品介绍

简支梁冲击试验机主要用于硬质塑料、增强尼龙、玻璃钢、陶瓷、铸石、电绝缘材料等非金属材料冲击韧性的测定,是化工行业、科研单位、大专院校质量检测等部门理想的试验设备。

二、简支梁冲击试验机特点

1 采用圆光栅测角技术,具有精度高、稳定性好和测量范围大等特点

2 具有数字化测量计算冲断功、冲击强度、计算一批试样的平均值等功能

3 预仰角、 升角校验方便

4 显示方式:液晶

三、简支梁冲击试验机符合标准:

GB/T3808-2018 摆锤式冲击试验机的检验

GB/T 1043-2008《硬质塑料简支梁冲击试验方法》;

GB/T 1843.1-2008《 塑料简支梁冲击性能的测定 第1部分:非仪器化冲击试验》;

GB∕T 1043.2-2018 塑料 简支梁冲击性能的测定 第2部分:仪器化冲击试验

ISO179:2010《Plastics-Determination of Charpy impact properties》;

ISO180:2000《Plastics-Determination of Izod impact strength》;

GB/T 18743-2002《流体输送用热塑性塑料管材简支梁冲击试验方法》(即适用于管材冲击)

GB/T 21189-2007塑料简支梁、悬臂梁和拉伸冲击试验用摆锤冲击试验机的检验

同时符合GB/T2611等标准的要求。

三、简支梁冲击试验机主要技术参数

1 冲击能量;1J 2J 4J 5J 7.5J 15J 25J 50J任选

2 摆锤预扬角:160 度

3 冲击速度:   2.9m/s(小于5J)   3.8m/s (大于5J)

   4 冲击刀刃夹角:30°

   5 钳口圆角半径:R1mm

   6 冲击刀刃圆角半径:R2mm

7 钳口支距:40mm   60mm 70mm 95mm

XJJ-5/50 Digital Display Shock Testing Machine for Simply Supported Beams

I. Product Introduction

Simply supported beam impact testing machine is mainly used to measure impact toughness of non-metallic materials such as hard plastics, reinforced nylon, fiberglass reinforced plastics, ceramics, cast stones, electrical insulation materials, etc. It is an ideal testing equipment for chemical industry, scientific research institutes, colleges and universities.

CHARACTERISTICS OF IMPACT TESTING MACHINE FOR SIMPLE SUPPORTED BEAMS

1. Using circular grating angle measurement technology, it has the characteristics of high accuracy, good stability and wide measurement range.

2. It has the functions of digital measurement and calculation of impulse power, impact strength and average value of a batch of samples.

3 Pre-elevation and elevation calibration is convenient

4 display mode: liquid crystal

3. Simply supported beam impact testing machine meets the standards:

GB/T3808-2018 "Inspection of Pendulum Impact Testing Machine"

GB/T 1043-2008 Impact Test Method for Hard Plastic Simply Supported Beams;

GB/T 1843.1-2008 "Determination of Impact Properties of Plastic Simply Supported Beams Part 2: Instrumented Impact Tests";

GB T 1043.2-2018 Determination of Impact Properties of Plastic Simply Supported Beams Part 2: Instrumented Impact Tests

ISO179:2010 Plastics-Determination of Charpy Impact Properties;

ISO180:2000 Plastics-Determination of Izod Impact Strength;

GB/T 18743-2002 Impact Test Method for Simply Supported Beams of Thermoplastic Pipes for Fluid Transportation

GB/T 21189-2007 "Inspection of Pendulum Impact Tester for Plastic Simply Supported Beams, Cantilever Beams and Tensile Impact Tests"

At the same time, it meets the requirements of GB/T 2611 and other standards.

Main Technical Parameters of Simply Supported Beam Impact Testing Machine

1 impact energy; 1J 2J 4J 5J 7.5J 15J 25J 50J optional

2 Pendulum Pre-lift Angle: 160 Degrees

3 Impact velocity: 2.9m/s (less than 5J) 3.8m/s (greater than 5J)

4 impact blade angle: 30 degrees

5-jaw rounded radius: R1mm

6 impact blade radius: R2mm

7 clamp pitch: 40mm 60mm 70mm 95mm